WEBVTT

1
00:00.000 --> 00:09.040
So this challenge involves adding a second V-Smart controller into our

2
00:09.040 --> 00:11.000
environment for redundancy.

3
00:11.000 --> 00:13.990
Now, in order to do that, we're going to have to start with a little bit of

4
00:13.990 --> 00:19.310
configuration here on our headquarters switch to prepare the port that we're

5
00:19.310 --> 00:20.000
going to put this in.

6
00:20.000 --> 00:24.000
So the first thing we're going to want to do is connect into the console here.

7
00:24.000 --> 00:27.000
And let's start with a show interface status.

8
00:27.000 --> 00:32.230
So what we're going to do is we're going to connect a second V-Smart controller
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

8
00:27.000 --> 00:32.230
So what we're going to do is we're going to connect a second V-Smart controller

9
00:32.230 --> 00:34.000
in here to port 3/3.

10
00:34.000 --> 00:37.000
Now, we can see we have some descriptions here.

11
00:37.000 --> 00:41.410
And although, of course, the description doesn't matter, it's probably a good

12
00:41.410 --> 00:45.000
idea to first go into interface gig 3/2

13
00:45.000 --> 00:53.000
and change our description to be linked to V-Smart 1.

14
00:53.000 --> 00:59.310
That way, we can go into our interface gig 3/3, change the description on that

15
00:59.310 --> 01:01.000
as the link to V-Smart 2.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

15
00:59.310 --> 01:01.000
as the link to V-Smart 2.

16
01:01.000 --> 01:06.950
Now, other configuration we're going to want is switch port mode access, switch

17
01:06.950 --> 01:10.000
port access for VLAN 100.

18
01:10.000 --> 01:16.000
And let's go ahead and turn on spanning tree port fast for an edge port.

19
01:16.000 --> 01:21.980
We'll exit configuration, do our show interface status again, and now we have

20
01:21.980 --> 01:27.000
our connections for both V-Smart 1 and V-Smart 2.

21
01:27.000 --> 01:30.820
So we'll save that configuration, and this should take care of the
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

21
01:27.000 --> 01:30.820
So we'll save that configuration, and this should take care of the

22
01:30.820 --> 01:34.000
configuration we need on our headquarters switch.

23
01:34.000 --> 01:40.000
So now, let's go into Cisco modeling labs and add our new device.

24
01:40.000 --> 01:45.190
Of course, if you're not using CML, you'll use the interface for whatever

25
01:45.190 --> 01:48.000
virtualization software you're using.

26
01:48.000 --> 01:52.550
So here in CML, the first thing we're going to want to do is rename this V-

27
01:52.550 --> 01:54.000
Smart controller.

28
01:54.000 --> 01:57.000
We'll simply make it V-Smart 1.

29
01:57.000 --> 01:59.000
We'll save those changes.

30
01:59.000 --> 02:04.620
And then, we'll come up here and add a new node, and we'll be adding a V-Smart
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

30
01:59.000 --> 02:04.620
And then, we'll come up here and add a new node, and we'll be adding a V-Smart

31
02:04.620 --> 02:06.000
controller.

32
02:06.000 --> 02:09.000
We'll just drag this and put it down here.

33
02:09.000 --> 02:11.000
Then we'll rename this.

34
02:11.000 --> 02:13.000
We'll make it V-Smart 2.

35
02:13.000 --> 02:15.000
Apply that.

36
02:15.000 --> 02:18.000
And then we have to make a new connection.

37
02:18.000 --> 02:20.000
So we'll right click on this.

38
02:20.000 --> 02:22.000
We'll say add a link.

39
02:22.000 --> 02:25.000
First, we're going to go to the headquarters switch.

40
02:25.000 --> 02:30.780
We're going to connect Ethernet 0 to the interface we just created and
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

40
02:25.000 --> 02:30.780
We're going to connect Ethernet 0 to the interface we just created and

41
02:30.780 --> 02:35.000
configured, which is our interface gigabit Ethernet 3.3.

42
02:35.000 --> 02:39.000
You can, of course, use whatever ports works in your environment.

43
02:39.000 --> 02:41.000
This is just how I'm building it.

44
02:41.000 --> 02:43.000
Then we'll say create link.

45
02:43.000 --> 02:46.680
And we'll want to connect this into our management network as well if you have

46
02:46.680 --> 02:49.000
the out of band management set up.

47
02:49.000 --> 02:51.000
So once again, we'll add a link.

48
02:51.000 --> 02:54.000
This one's going to go to our management switch.

49
02:54.000 --> 02:57.000
And here we're going to connect Ethernet 1, 2.

50
02:57.000 --> 03:01.000
In this case, they're all in the same VLAN on that management switch.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

50
02:57.000 --> 03:01.000
In this case, they're all in the same VLAN on that management switch.

51
03:01.000 --> 03:04.000
It's actually an unmanaged switch.

52
03:04.000 --> 03:09.000
So we can disconnect this to whatever port we like and we'll hit create link.

53
03:09.000 --> 03:12.000
So now we have our second V-Smart controller built.

54
03:12.000 --> 03:14.000
Now we need to fire it up.

55
03:14.000 --> 03:16.000
So let's right click on it.

56
03:16.000 --> 03:18.000
We'll start that node.

57
03:18.000 --> 03:23.250
Now let's use CML's built-in terminal server to connect to the console on that

58
03:23.250 --> 03:25.000
V-Smart controller.

59
03:25.000 --> 03:28.000
This will, of course, take quite a few moments to boot up.

60
03:28.000 --> 03:33.000
So we'll skip ahead until when our V-Smart 2 controller is online.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

60
03:28.000 --> 03:33.000
So we'll skip ahead until when our V-Smart 2 controller is online.

61
03:33.000 --> 03:35.000
So now it's fully booted up.

62
03:35.000 --> 03:39.600
If you look up at the top, you can see my auto log in already tried to log us

63
03:39.600 --> 03:40.000
in.

64
03:40.000 --> 03:43.000
The system wasn't quite up yet and it was incorrect.

65
03:43.000 --> 03:45.000
So that's not going to work.

66
03:45.000 --> 03:47.000
But we do need to configure our login.

67
03:47.000 --> 03:51.000
So we need to log in first with admin admin.

68
03:51.000 --> 03:54.000
Again, my auto login is getting in the way.

69
03:54.000 --> 03:56.000
This is because we have the wrong password set.

70
03:56.000 --> 03:58.000
Now it wants to new one.

71
03:58.000 --> 04:01.000
So now we can put in the password we've been using through all of this.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

71
03:58.000 --> 04:01.000
So now we can put in the password we've been using through all of this.

72
04:01.000 --> 04:04.000
The one, two, three, four, Q, W, E, R.

73
04:04.000 --> 04:07.000
And now we're left at the command prompt.

74
04:07.000 --> 04:10.000
Now we can put in our baseline configuration.

75
04:10.000 --> 04:14.630
Now this is the same as all of the other devices we've done, except the IP

76
04:14.630 --> 04:16.000
address is different.

77
04:16.000 --> 04:19.000
So we're just going to copy and paste this in.

78
04:19.000 --> 04:24.130
So if we take a look over this, notice again all the IP addresses are simply .

79
04:24.130 --> 04:27.000
218 as we were told to configure.

80
04:27.000 --> 04:33.000
And the other thing that's different, of course, is the host name is vSmart2.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

80
04:27.000 --> 04:33.000
And the other thing that's different, of course, is the host name is vSmart2.

81
04:33.000 --> 04:36.000
So let's go ahead and configure this.

82
04:36.000 --> 04:39.000
So that should take care of the basic configuration here.

83
04:39.000 --> 04:45.070
Let's see if we can do a ping of 10, 100, 10, 10, 2, 15, which is our V managed

84
04:45.070 --> 04:46.000
controller.

85
04:46.000 --> 04:48.000
We can see that that's functional.

86
04:48.000 --> 04:53.550
We should also be able to ping our two 16 and two 17, which of course is the

87
04:53.550 --> 04:56.000
other vSmart controller.

88
04:56.000 --> 04:59.000
We should also be able to ping our management network.

89
04:59.000 --> 05:05.000
So we'll do a ping VPN 512 to 192.168.1.1.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

89
04:59.000 --> 05:05.000
So we'll do a ping VPN 512 to 192.168.1.1.

90
05:05.000 --> 05:10.930
And that's also successful, which also means we should now be able to switch

91
05:10.930 --> 05:14.000
from the console to an SSH connection.

92
05:14.000 --> 05:19.000
So if we connect to SSH, it's asking for our new host key.

93
05:19.000 --> 05:21.000
We'll say accept and save.

94
05:21.000 --> 05:24.000
And now we're on vSmart2 through SSH.

95
05:24.000 --> 05:26.000
So now we can close the console.

96
05:26.000 --> 05:32.260
So with the console closed, let's also connect to our old vSmart controller,
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

96
05:26.000 --> 05:32.260
So with the console closed, let's also connect to our old vSmart controller,

97
05:32.260 --> 05:36.000
because one of the other things we're supposed to do is rename that controller.

98
05:36.000 --> 05:42.380
So here on vSmart1, we'll simply go into configuration mode, into system, and

99
05:42.380 --> 05:46.000
set the host name to vSmart1.

100
05:46.000 --> 05:48.000
We'll do our commit and quit.

101
05:48.000 --> 05:51.990
And that's all we had to configure on vSmart1 so we can just close out of v

102
05:51.990 --> 05:53.000
Smart1 now.

103
05:53.000 --> 05:59.000
Our final step is then to install our certificate here on vSmart2.

104
05:59.000 --> 06:04.000
So the first thing we need to do is copy that from vManage.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

104
05:59.000 --> 06:04.000
So the first thing we need to do is copy that from vManage.

105
06:04.000 --> 06:06.000
So let's go over to the vManage device.

106
06:06.000 --> 06:09.000
On vManage, we're going to vShell.

107
06:09.000 --> 06:12.000
Remember, this is where our actual certificate is.

108
06:12.000 --> 06:14.000
And then we'll scp.

109
06:14.000 --> 06:22.000
We're going to copy CACRT as admin to the 10.100.10.218.

110
06:22.000 --> 06:28.000
We'll accept the fingerprint, add our password, and the files copied.

111
06:28.000 --> 06:33.000
So now all we have to do is go back to vSmart2 and install our certificate.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

111
06:28.000 --> 06:33.000
So now all we have to do is go back to vSmart2 and install our certificate.

112
06:33.000 --> 06:37.970
Remember, the command for that is to request the root cert chain to be

113
06:37.970 --> 06:41.000
installed, and then we point to that root certificate.

114
06:41.000 --> 06:44.000
It successfully installs the chain.

115
06:44.000 --> 06:49.410
So now we have our second vSmart controller up online ready to be added into

116
06:49.410 --> 06:51.000
our environment.

117
06:51.000 --> 06:57.000
So that concludes this challenge and therefore this skill.

118
06:57.000 --> 07:02.000
Congratulations on completing ConfigureRSDWAN environment.
WEBVTT
X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000

118
06:57.000 --> 07:02.000
Congratulations on completing ConfigureRSDWAN environment.

119
07:02.000 --> 07:05.830
I hope this has been informative for you, and I'd like to thank you for viewing

120
07:05.830 --> 07:06.000
.

121
07:06.000 --> 07:21.980
Thank you for watching.