WEBVTT

00:00:00.000 --> 00:00:03.451 align:middle line:90%


00:00:03.451 --> 00:00:06.902 align:middle line:90%
[AUDIO LOGO]

00:00:06.902 --> 00:00:09.870 align:middle line:90%


00:00:09.870 --> 00:00:12.150 align:middle line:90%
Hello and welcome to INE.

00:00:12.150 --> 00:00:15.030 align:middle line:84%
Today, in this video, we
would look at section 1--

00:00:15.030 --> 00:00:19.350 align:middle line:84%
Phone Registration and
IM&P, basically Task 1.4.

00:00:19.350 --> 00:00:23.340 align:middle line:84%
Here it says that users in
Site B need to log into Jabber.

00:00:23.340 --> 00:00:25.680 align:middle line:84%
Ensure the following
requirements are met.

00:00:25.680 --> 00:00:27.397 align:middle line:84%
Configure user,
STEVE ROGERS, with

00:00:27.397 --> 00:00:28.980 align:middle line:84%
the following
requirements-- extension

00:00:28.980 --> 00:00:31.620 align:middle line:90%
should be set to 3003.

00:00:31.620 --> 00:00:34.620 align:middle line:84%
Use Trivial caller names
such as Steve Rogers.

00:00:34.620 --> 00:00:37.290 align:middle line:84%
The phone should display
globalized calling number

00:00:37.290 --> 00:00:42.030 align:middle line:84%
as +19723033003 on the top
left-hand corner of the phone

00:00:42.030 --> 00:00:44.400 align:middle line:90%
system or the phone screen.

00:00:44.400 --> 00:00:47.760 align:middle line:84%
Manually configure the
advanced settings in Jabber

00:00:47.760 --> 00:00:50.790 align:middle line:90%
to allow users to log in.

00:00:50.790 --> 00:00:54.540 align:middle line:84%
And once complete, log into
Jabber2 PC using the account

00:00:54.540 --> 00:00:56.970 align:middle line:90%
steve-rogers@ine.com.

00:00:56.970 --> 00:00:59.460 align:middle line:90%
Now, this is our requirement.

00:00:59.460 --> 00:01:03.520 align:middle line:84%
Now if you remember,
from the earlier task,

00:01:03.520 --> 00:01:07.830 align:middle line:84%
we had basically
configured a manual--

00:01:07.830 --> 00:01:09.900 align:middle line:90%
a local user, Steve Rogers.

00:01:09.900 --> 00:01:16.500 align:middle line:84%
And that user had the service
profile and the IM&P enabled.

00:01:16.500 --> 00:01:19.200 align:middle line:84%
It had the access
group permissions,

00:01:19.200 --> 00:01:21.030 align:middle line:84%
but it did not
have any extension.

00:01:21.030 --> 00:01:22.650 align:middle line:84%
So obviously, at
that point of time,

00:01:22.650 --> 00:01:24.480 align:middle line:84%
we were not able
to log into Jabber.

00:01:24.480 --> 00:01:27.600 align:middle line:84%
But this time, we will log
into Jabber using that account,

00:01:27.600 --> 00:01:31.810 align:middle line:84%
but we would not be
using the SRV record,

00:01:31.810 --> 00:01:35.402 align:middle line:84%
so we would not
be doing a lookup.

00:01:35.402 --> 00:01:37.860 align:middle line:84%
Instead, we would configure
the advanced settings in Jabber

00:01:37.860 --> 00:01:42.090 align:middle line:84%
to define the IP address
or the FQDN of the IM&P.

00:01:42.090 --> 00:01:48.240 align:middle line:84%
So let's go to my Jabber1 PC to
access my call manager, which

00:01:48.240 --> 00:01:50.700 align:middle line:90%
is the Site B. Let's close this.

00:01:50.700 --> 00:01:53.400 align:middle line:84%
And this is one
which is for Site B.

00:01:53.400 --> 00:02:01.260 align:middle line:84%
And let's go to User Management,
to End Users, and let's

00:02:01.260 --> 00:02:03.240 align:middle line:90%
go to a Find.

00:02:03.240 --> 00:02:05.470 align:middle line:84%
And look at the account
that we created earlier.

00:02:05.470 --> 00:02:08.970 align:middle line:84%
So this was the account that we
had done earlier, Steve Rogers.

00:02:08.970 --> 00:02:13.260 align:middle line:84%
And if you see there's no
Device Association done,

00:02:13.260 --> 00:02:18.720 align:middle line:84%
there's no Primary Extension,
and we have the access group

00:02:18.720 --> 00:02:19.410 align:middle line:90%
permission.

00:02:19.410 --> 00:02:22.680 align:middle line:84%
Now, for HQ side, we didn't have
to define the primary extension

00:02:22.680 --> 00:02:24.540 align:middle line:84%
because that was
automatically assigned

00:02:24.540 --> 00:02:26.940 align:middle line:90%
when we imported the LDAP user.

00:02:26.940 --> 00:02:28.890 align:middle line:84%
But because this
is a local user,

00:02:28.890 --> 00:02:31.890 align:middle line:84%
I would have to manually
define the primary extension.

00:02:31.890 --> 00:02:35.670 align:middle line:84%
So the first thing that I would
do is go to Device, Phone,

00:02:35.670 --> 00:02:39.620 align:middle line:84%
and create a CSF,
so let's do Add New.

00:02:39.620 --> 00:02:45.560 align:middle line:84%
Scroll all the way down and look
for Client Services Framework

00:02:45.560 --> 00:02:47.690 align:middle line:90%
and do Next.

00:02:47.690 --> 00:02:51.980 align:middle line:84%
Let's give the
name as CSFROGERS.

00:02:51.980 --> 00:02:56.390 align:middle line:84%
The description would
be Steve Rogers.

00:02:56.390 --> 00:02:59.270 align:middle line:84%
My Device Pool would
be the Default. Phone

00:02:59.270 --> 00:03:01.580 align:middle line:90%
template is the Default.

00:03:01.580 --> 00:03:06.230 align:middle line:84%
The Owner is going
to be steve-rogers.

00:03:06.230 --> 00:03:09.030 align:middle line:84%
And then define my
Device Security Profile,

00:03:09.030 --> 00:03:10.790 align:middle line:84%
which is the default
one, which is

00:03:10.790 --> 00:03:13.970 align:middle line:84%
going to be the Client
Services Framework Standard SIP

00:03:13.970 --> 00:03:16.160 align:middle line:90%
Non-Secure Profile.

00:03:16.160 --> 00:03:17.840 align:middle line:84%
And the SIP profile
is, again, going

00:03:17.840 --> 00:03:19.250 align:middle line:90%
to be the Standard SIP profile.

00:03:19.250 --> 00:03:21.970 align:middle line:90%
Let's save this.

00:03:21.970 --> 00:03:25.200 align:middle line:84%
And then let's
create an extension.

00:03:25.200 --> 00:03:28.370 align:middle line:90%
So add DN.

00:03:28.370 --> 00:03:31.430 align:middle line:90%
This is 3003.

00:03:31.430 --> 00:03:36.110 align:middle line:84%
The name is going
to be Steve Rogers.

00:03:36.110 --> 00:03:38.980 align:middle line:90%
Steve Rogers.

00:03:38.980 --> 00:03:44.420 align:middle line:90%


00:03:44.420 --> 00:03:46.520 align:middle line:90%
And let's copy this.

00:03:46.520 --> 00:03:47.270 align:middle line:90%
Scroll down.

00:03:47.270 --> 00:03:49.640 align:middle line:84%
I don't really do any changes
in the Voice Mail Profile

00:03:49.640 --> 00:03:52.040 align:middle line:84%
or Calling Search Space
at this point of time

00:03:52.040 --> 00:03:54.440 align:middle line:84%
because I'm not really
doing dial plan.

00:03:54.440 --> 00:03:55.730 align:middle line:90%
And scroll down.

00:03:55.730 --> 00:03:57.050 align:middle line:90%
No Voice Mail settings.

00:03:57.050 --> 00:03:59.960 align:middle line:84%
Scroll all the way down and
define the Display Caller

00:03:59.960 --> 00:04:02.840 align:middle line:90%
ID as Steve Rogers.

00:04:02.840 --> 00:04:06.140 align:middle line:84%
And the External Phone
Number Mask is going to be

00:04:06.140 --> 00:04:13.070 align:middle line:90%
+19723033003.

00:04:13.070 --> 00:04:18.070 align:middle line:84%
And then Busy Trigger, keep
it as default, and Save.

00:04:18.070 --> 00:04:21.370 align:middle line:84%
Now once we save this, because
we want the present status,

00:04:21.370 --> 00:04:23.950 align:middle line:84%
I would go down all the
way here and Associate

00:04:23.950 --> 00:04:28.530 align:middle line:84%
the End User, which is
going to be Steve Rogers.

00:04:28.530 --> 00:04:30.540 align:middle line:90%
And Save this.

00:04:30.540 --> 00:04:36.090 align:middle line:84%
Now go back to your End User
and do a Device Association

00:04:36.090 --> 00:04:37.320 align:middle line:90%
with the CSF.

00:04:37.320 --> 00:04:42.990 align:middle line:84%
Let's scroll down, do
a Device Association.

00:04:42.990 --> 00:04:44.940 align:middle line:90%
Let's do Find.

00:04:44.940 --> 00:04:48.640 align:middle line:90%
And attach our CSF.

00:04:48.640 --> 00:04:52.890 align:middle line:90%
Go back and Save this.

00:04:52.890 --> 00:04:54.070 align:middle line:90%
Now, scroll back down.

00:04:54.070 --> 00:04:56.040 align:middle line:84%
Don't forget the
Primary Extension

00:04:56.040 --> 00:04:58.110 align:middle line:90%
because this is a local user.

00:04:58.110 --> 00:05:00.330 align:middle line:84%
You need to define
the Primary Extension.

00:05:00.330 --> 00:05:02.340 align:middle line:90%
That's going to be 3003.

00:05:02.340 --> 00:05:03.520 align:middle line:90%
Let's save that.

00:05:03.520 --> 00:05:05.010 align:middle line:84%
Now because we want
present status,

00:05:05.010 --> 00:05:08.280 align:middle line:84%
I would also need to
go to Device, Trunk,

00:05:08.280 --> 00:05:11.580 align:middle line:84%
create a SIP Trunk to
my IM&P. Now one thing,

00:05:11.580 --> 00:05:14.040 align:middle line:84%
also verify that because
this is a local user,

00:05:14.040 --> 00:05:16.200 align:middle line:84%
we did not use the
feature group templates.

00:05:16.200 --> 00:05:19.800 align:middle line:84%
We should go and check
if the IM&P is enabled

00:05:19.800 --> 00:05:22.860 align:middle line:84%
and the Service Profile that
we had done in earlier task

00:05:22.860 --> 00:05:25.480 align:middle line:90%
is applied to this end user.

00:05:25.480 --> 00:05:28.950 align:middle line:84%
So let's now go back
to Device, Trunk,

00:05:28.950 --> 00:05:34.460 align:middle line:84%
create a SIP Trunk to
my IM&P. Let's do Next.

00:05:34.460 --> 00:05:47.670 align:middle line:84%
And let's name this
as SIP-TRUNK-IM-P.

00:05:47.670 --> 00:05:51.800 align:middle line:84%
Description or the Device
Pool is going to be Default.

00:05:51.800 --> 00:05:53.260 align:middle line:90%
Let's scroll down.

00:05:53.260 --> 00:05:54.855 align:middle line:84%
You could do Run On
All Active Nodes.

00:05:54.855 --> 00:05:56.230 align:middle line:84%
I don't really
have a subscriber,

00:05:56.230 --> 00:05:58.110 align:middle line:84%
so we don't really
have to do this.

00:05:58.110 --> 00:05:59.280 align:middle line:90%
Scroll down.

00:05:59.280 --> 00:06:00.720 align:middle line:90%
Inbound.

00:06:00.720 --> 00:06:03.210 align:middle line:84%
Redirect Diversion
Header for Inbound.

00:06:03.210 --> 00:06:07.320 align:middle line:84%
And redirect Diversion
Header for Outbound.

00:06:07.320 --> 00:06:09.240 align:middle line:90%
Let's scroll down.

00:06:09.240 --> 00:06:12.240 align:middle line:84%
Define the address of IM&P,
which is sb-imp.ine.com.

00:06:12.240 --> 00:06:14.457 align:middle line:90%


00:06:14.457 --> 00:06:16.290 align:middle line:84%
Again, if you're not
really sure about this,

00:06:16.290 --> 00:06:19.650 align:middle line:84%
go back to your DNS
machine and check FQDN.

00:06:19.650 --> 00:06:21.965 align:middle line:84%
What's the name of
the machine and what's

00:06:21.965 --> 00:06:24.090 align:middle line:84%
the fully qualified domain
name and the IP address?

00:06:24.090 --> 00:06:26.590 align:middle line:84%
You can give the IP address
here or you could give the FQDN.

00:06:26.590 --> 00:06:29.910 align:middle line:84%
As long as you have DNS
running, you should be OK.

00:06:29.910 --> 00:06:37.020 align:middle line:84%
So sb-imp.ine.com, which is
your IM&P presence for Site B.

00:06:37.020 --> 00:06:40.020 align:middle line:84%
The SIP Trunk profile is going
to be the Default Non Secure

00:06:40.020 --> 00:06:40.530 align:middle line:90%
Profile.

00:06:40.530 --> 00:06:43.110 align:middle line:84%
And the SIP profile is going
to be the standard one.

00:06:43.110 --> 00:06:48.405 align:middle line:90%
Let's Save this and Reset.

00:06:48.405 --> 00:06:51.400 align:middle line:90%


00:06:51.400 --> 00:06:52.990 align:middle line:84%
Then go back and
publish this Trunk

00:06:52.990 --> 00:06:57.250 align:middle line:84%
through your IM&P, which is
inside Service Parameters.

00:06:57.250 --> 00:07:03.805 align:middle line:84%
Go back to your call manager
and search for Presence.

00:07:03.805 --> 00:07:08.420 align:middle line:90%


00:07:08.420 --> 00:07:09.770 align:middle line:90%
Define your Trunk here.

00:07:09.770 --> 00:07:13.670 align:middle line:84%
This should publish this Trunk
to the IM&P for your Presence

00:07:13.670 --> 00:07:14.870 align:middle line:90%
status.

00:07:14.870 --> 00:07:19.035 align:middle line:84%
And once this is done,
before we log in to Jabber,

00:07:19.035 --> 00:07:20.660 align:middle line:84%
one more check you
should do because we

00:07:20.660 --> 00:07:22.730 align:middle line:84%
don't want the same
error of not being

00:07:22.730 --> 00:07:24.467 align:middle line:90%
able to contact the services.

00:07:24.467 --> 00:07:27.050 align:middle line:84%
So go back to Server and check
if you have the fully qualified

00:07:27.050 --> 00:07:27.800 align:middle line:90%
domain name.

00:07:27.800 --> 00:07:30.920 align:middle line:84%
Because if you look at the UC
Service that we had defined

00:07:30.920 --> 00:07:36.380 align:middle line:84%
earlier in the earlier task,
we had defined the FQDN,

00:07:36.380 --> 00:07:40.040 align:middle line:90%
which was sb-cucm.ine.com.

00:07:40.040 --> 00:07:44.660 align:middle line:84%
So let's go back to Servers
and check if that is OK.

00:07:44.660 --> 00:07:46.490 align:middle line:84%
So again, there's the
same problem here.

00:07:46.490 --> 00:07:49.610 align:middle line:84%
The Site B CUCM is not defined
as a fully qualified domain

00:07:49.610 --> 00:07:50.430 align:middle line:90%
name.

00:07:50.430 --> 00:07:53.360 align:middle line:84%
So this would not resolve by
the DNS because DNS is resolving

00:07:53.360 --> 00:07:56.990 align:middle line:90%
him as sb-cucm.ine.com.

00:07:56.990 --> 00:08:02.585 align:middle line:90%
So .ine.com and save this.

00:08:02.585 --> 00:08:03.960 align:middle line:84%
I think that's
all we need to do.

00:08:03.960 --> 00:08:09.240 align:middle line:84%
Now let's go back to the EVE
Topology and go to Jabber2.

00:08:09.240 --> 00:08:15.120 align:middle line:84%
And on Jabber2 machine,
we would log into Jabber.

00:08:15.120 --> 00:08:21.120 align:middle line:84%
But this time, because we didn't
really create an SRV record,

00:08:21.120 --> 00:08:24.810 align:middle line:90%
we would have to do it manually.

00:08:24.810 --> 00:08:30.330 align:middle line:84%
Because there is no record
for sb.ine.com on my DNS,

00:08:30.330 --> 00:08:32.909 align:middle line:84%
so I would have to manually
define the settings,

00:08:32.909 --> 00:08:35.695 align:middle line:84%
define which IM&P
actually connecting to.

00:08:35.695 --> 00:08:38.070 align:middle line:84%
Because if I don't define
that, and if I just try and log

00:08:38.070 --> 00:08:43.919 align:middle line:84%
in with steve-rogers@ine.com,
he would actually contact the HQ

00:08:43.919 --> 00:08:46.300 align:middle line:90%
site and try logging in there.

00:08:46.300 --> 00:08:47.920 align:middle line:90%
We don't really want that.

00:08:47.920 --> 00:08:51.510 align:middle line:90%
So let's look at my Jabber.

00:08:51.510 --> 00:08:53.085 align:middle line:84%
So I have my Jabber
on my desktop.

00:08:53.085 --> 00:08:57.980 align:middle line:90%


00:08:57.980 --> 00:09:01.300 align:middle line:84%
Let's open that up and
go to Advanced settings,

00:09:01.300 --> 00:09:05.290 align:middle line:84%
select IM&P and define
the address of IM&P, which

00:09:05.290 --> 00:09:11.650 align:middle line:90%
is sb.imp.ine.com, and Save.

00:09:11.650 --> 00:09:19.240 align:middle line:84%
Let's now say
steve-rogers@ine.com

00:09:19.240 --> 00:09:20.300 align:middle line:90%
and Continue.

00:09:20.300 --> 00:09:22.390 align:middle line:84%
So this should point
to IM&P of Site B

00:09:22.390 --> 00:09:24.580 align:middle line:90%
because we manually define that.

00:09:24.580 --> 00:09:26.590 align:middle line:90%
Let's login with C1SC0123!

00:09:26.590 --> 00:09:29.770 align:middle line:90%
and sign in.

00:09:29.770 --> 00:09:36.310 align:middle line:84%
It should give me the certs for
the IM&P and my call manager.

00:09:36.310 --> 00:09:40.330 align:middle line:90%
And I should be able to log in.

00:09:40.330 --> 00:09:42.550 align:middle line:84%
Now once I log in,
the phone which

00:09:42.550 --> 00:09:44.830 align:middle line:84%
is associated with
this user is going

00:09:44.830 --> 00:09:47.560 align:middle line:90%
to be the CSF that we created.

00:09:47.560 --> 00:09:50.200 align:middle line:84%
Again, at this system
error, just say OK for that

00:09:50.200 --> 00:09:51.730 align:middle line:90%
and say Accept.

00:09:51.730 --> 00:09:54.850 align:middle line:84%
So I was able to log
into Steve Rogers.

00:09:54.850 --> 00:09:59.110 align:middle line:84%
If you look at the name, because
we didn't do a UDS lookup,

00:09:59.110 --> 00:10:02.800 align:middle line:84%
the SRV lookup, it shows
as steve-rogers@ine.com.

00:10:02.800 --> 00:10:06.640 align:middle line:84%
Otherwise, you would
only see steve-rogers.

00:10:06.640 --> 00:10:10.570 align:middle line:84%
And if I look down, I should
see the phone associated,

00:10:10.570 --> 00:10:13.570 align:middle line:84%
which it has, which you
can see here that I'm

00:10:13.570 --> 00:10:15.700 align:middle line:90%
using my computer for calls.

00:10:15.700 --> 00:10:18.280 align:middle line:84%
Again, I cannot really make
any calls at this point of time

00:10:18.280 --> 00:10:21.130 align:middle line:84%
because I don't really have any
dial plan configured between

00:10:21.130 --> 00:10:24.130 align:middle line:84%
the sites, but you're able to
log in, which basically means

00:10:24.130 --> 00:10:28.000 align:middle line:84%
that you've met the
requirements of the question.

00:10:28.000 --> 00:10:30.540 align:middle line:84%
We use the Trivial name
correctly as Steve Rogers.

00:10:30.540 --> 00:10:32.830 align:middle line:90%
The extension was 3003.

00:10:32.830 --> 00:10:38.584 align:middle line:84%
And the external phone number
mask was set to +19723033003.

00:10:38.584 --> 00:10:42.190 align:middle line:90%


00:10:42.190 --> 00:10:49.480 align:middle line:84%
And I believe that we configured
the present status, which

00:10:49.480 --> 00:10:53.200 align:middle line:84%
basically means that if he's on
a call, it should show as busy.

00:10:53.200 --> 00:11:05.960 align:middle line:84%
For example, let's say if I
try and dial myself, 3003--

00:11:05.960 --> 00:11:09.860 align:middle line:84%
if I try and dial myself,
my present status, which you

00:11:09.860 --> 00:11:11.430 align:middle line:90%
can see here--

00:11:11.430 --> 00:11:13.650 align:middle line:90%
let's go back to here.

00:11:13.650 --> 00:11:16.970 align:middle line:84%
You can see On a call,
which basically means--

00:11:16.970 --> 00:11:18.390 align:middle line:90%
Let me share my screen.

00:11:18.390 --> 00:11:20.510 align:middle line:84%
So when I make the
call, you can see

00:11:20.510 --> 00:11:24.470 align:middle line:84%
that it shows On a call, which
means your presence status is

00:11:24.470 --> 00:11:25.040 align:middle line:90%
working.

00:11:25.040 --> 00:11:27.708 align:middle line:84%
When I end the call,
it shows Available.

00:11:27.708 --> 00:11:29.000 align:middle line:90%
So that's your presence status.

00:11:29.000 --> 00:11:31.010 align:middle line:84%
We know it's working
because of your SIP Trunk

00:11:31.010 --> 00:11:35.280 align:middle line:84%
that we published to your IM&P.
So any time he goes on a call,

00:11:35.280 --> 00:11:37.580 align:middle line:84%
it would show as
On a call or Busy,

00:11:37.580 --> 00:11:40.130 align:middle line:84%
or Available if
he's not on a call.

00:11:40.130 --> 00:11:42.740 align:middle line:84%
With this, we've met all of the
requirements of the question.

00:11:42.740 --> 00:11:44.640 align:middle line:84%
I hope this video was
informative to you.

00:11:44.640 --> 00:11:47.200 align:middle line:90%
And thank you for watching.

00:11:47.200 --> 00:11:48.000 align:middle line:90%