1
00:00:07,300 --> 00:00:15,610
Well we have different grounds to the same destination and the roads all have the same road attributes

2
00:00:16,150 --> 00:00:25,970
that is distance priority or maybe metric then differing it will load balanced the traffic.

3
00:00:25,970 --> 00:00:36,050
Now this is called equal cost multi path ICMP but we can change the way or the parameters that 48 loan

4
00:00:36,050 --> 00:00:38,090
balances the traffic.

5
00:00:38,090 --> 00:00:39,470
Let's see how we do it.

6
00:00:40,620 --> 00:00:46,680
Let's get over to our command line config system settings

7
00:00:54,490 --> 00:00:58,170
set V4 ECM P mode.

8
00:00:58,200 --> 00:01:04,270
Now if you scroll you will see four different methods.

9
00:01:04,270 --> 00:01:11,260
The first one source IP based all traffic that comes from the same source will be destined to the same

10
00:01:11,350 --> 00:01:16,660
route weighted IP based wav IP based.

11
00:01:16,750 --> 00:01:26,390
That is all traffic will be routed or will be distributed between different interfaces.

12
00:01:26,680 --> 00:01:33,760
And that is according to a weak number that we will configure on the different interface.

13
00:01:33,760 --> 00:01:39,740
We will look at it in a minute usage IP based.

14
00:01:39,910 --> 00:01:47,890
All traffic will be distributed towards a specific interface.

15
00:01:48,040 --> 00:01:52,760
And that is until a volume threshold is approached.

16
00:01:52,840 --> 00:02:00,190
We will also see how we configure and volume threshold to an interface.

17
00:02:00,190 --> 00:02:06,910
When it approaches the threshold approaches then the traffic will move to another route.

18
00:02:07,810 --> 00:02:10,630
And the last one is the source destination IP.

19
00:02:10,960 --> 00:02:13,180
And that is the same as source site.

20
00:02:13,210 --> 00:02:15,570
But it also includes the destination.

21
00:02:15,580 --> 00:02:23,110
That is all traffic that comes from the same source and destined to the same destination will follow

22
00:02:23,110 --> 00:02:25,660
the same route.

23
00:02:26,130 --> 00:02:30,850
That's config await to our

24
00:02:33,720 --> 00:02:35,120
tor interface.

25
00:02:40,560 --> 00:02:46,120
Let's use when one set way.

26
00:02:46,710 --> 00:02:52,140
And now higher weights are likely to be chosen.

27
00:02:52,140 --> 00:03:00,060
That is the traffic will be distributed between the different interfaces all the different rules but

28
00:03:00,150 --> 00:03:06,630
interfaces or routes that has higher weights will probably get more traffic.

29
00:03:06,630 --> 00:03:15,050
Now we can set up the weight between 0 and 255 so let's set it up to two hundred and fifty five.

30
00:03:15,810 --> 00:03:17,260
And that's it.

31
00:03:18,920 --> 00:03:30,050
So if we choose the wafer PE method one one would probably get more traffic than other arouse other

32
00:03:30,050 --> 00:03:38,860
same routes that has lower weights when we use these pill over method.

33
00:03:38,870 --> 00:03:48,350
That is when threshold volume is approached on a specific round or an interface the traffic will flow

34
00:03:48,350 --> 00:03:51,560
to the second route.

35
00:03:51,560 --> 00:03:55,430
Now how do we set up a volume threshold.

36
00:03:55,430 --> 00:04:00,110
We use the same config sys interface.

37
00:04:00,560 --> 00:04:10,960
Edit the interface or the rule that we want to configure the threshold and then we use the set spill

38
00:04:10,960 --> 00:04:19,820
over threshold and that is a value between 0 and 16 million so that's just choose

39
00:04:27,700 --> 00:04:28,510
no right.